Sealand HTS Holding Tanks Basic Fittings Bedienungsanleitung

Stöbern Sie online oder laden Sie Bedienungsanleitung nach Zubehör fürs Wasser Sealand HTS Holding Tanks Basic Fittings herunter. SeaLand HTS Holding Tanks Basic Fittings User Manual Benutzerhandbuch

  • Herunterladen
  • Zu meinen Handbüchern hinzufügen
  • Drucken
  • Seite
    / 1
  • Inhaltsverzeichnis
  • LESEZEICHEN
  • Bewertet. / 5. Basierend auf Kundenbewertungen
Seitenansicht 0
HTS Fittings Installation
for HTS holding tanks
HTS Fittings Installation
for HTS holding tanks
® Registered; ™ Trademark of Dometic Corporation
© Dometic Corporation
600346786 01 01/12
® Registered; ™ Trademark of Dometic Corporation
© Dometic Corporation
600346786 01 01/12
3-inch cap – inspection port
1. Place cap into 3-inch (76 mm) threaded hole
(g.
1
) and tighten until hand-tight.
2. Using spanner wrench or large channel
locks, tighten cap until very little or no black
seal is visible above inlet port (g.
2
).
3. To remove cap for tank inspection, use
spanner wrench or large channel locks.
3-inch cap – inspection port
1. Place cap into 3-inch (76 mm) threaded hole
(g.
1
) and tighten until hand-tight.
2. Using spanner wrench or large channel
locks, tighten cap until very little or no black
seal is visible above inlet port (g.
2
).
3. To remove cap for tank inspection, use
spanner wrench or large channel locks.
Inlet and discharge elbow fittings
1. Apply threaded plastic pipe sealant around
threads of elbow (g.
3
).
2. Tighten elbow into desired tting on tank
(g.
4
).
3. To properly position elbow to receive
sanitation hose, turn elbow only in clockwise
direction (g.
4
). (Turning the elbow in
opposite direction may loosen connection
and cause leakage.)
4. Make sure to connect waste discharge
hose(s) to tting(s) marked as “Waste Only.
5. When connecting sanitation hose to plastic
elbows, use silicone grease on end of tting
and inside hose end to help make connec-
tion easier and leakproof. Be sure to use two
hose clamps to secure each connection.
Inlet and discharge elbow fittings
1. Apply threaded plastic pipe sealant around
threads of elbow (g.
3
).
2. Tighten elbow into desired tting on tank
(g.
4
).
3. To properly position elbow to receive
sanitation hose, turn elbow only in clockwise
direction (g.
4
). (Turning the elbow in
opposite direction may loosen connection
and cause leakage.)
4. Make sure to connect waste discharge
hose(s) to tting(s) marked as “Waste Only.
5. When connecting sanitation hose to plastic
elbows, use silicone grease on end of tting
and inside hose end to help make connec-
tion easier and leakproof. Be sure to use two
hose clamps to secure each connection.
2 2
4 4
1 1
3 3
IF SEALAND TANK FITTINGS ARE NOT ASSEMBLED TO TANK,
FOLLOW THESE INSTRUCTIONS.
IF SEALAND TANK FITTINGS ARE NOT ASSEMBLED TO TANK,
FOLLOW THESE INSTRUCTIONS.
Refer to SeaLand Holding Tank
System (HTS) owner’s manual for
complete system installation.
Refer to SeaLand Holding Tank
System (HTS) owner’s manual for
complete system installation.
Seitenansicht 0
1

Inhaltsverzeichnis

Seite 1 - HTS Fittings Installation

HTS Fittings Installationfor HTS holding tanksHTS Fittings Installationfor HTS holding tanks® Registered; ™ Trademark of Dometic Corporation© Dometic

Kommentare zu diesen Handbüchern

Keine Kommentare